FPV (5) - (3) inch analog drone equipment ALL NEW / Radios / Goggles

Description

UNDERSTANDING
the condition for pilots whom do fly and are self builders I'll try to help include the necessary information for this BEAST of a bundle!
PRICE IS GOING  FOR
2000
IN SHIPPING
for handing care.!
WONT SEE THIS ACTION ANYWHERE ELSE & LIMITED TIME & TAKEN CARE OF :D
~>This is great for people wanting to drive straight into the FPV HOBBIE!!
List of main items are as to be followed
~>
TORVOL FPV BAG
FRSKYX9 LITE
-comes already installed TBS Tracer moduleRADIOMASTERTX16S
-comes already installed TBS Crossfire module
SKYZONE 02C FPV GOGGLES
-comes painted white and orangeFATSHARK HDO1 OLED FPV GOGGLES
-comes already installed RAPIDFIRE moduleGOPRO HERO 11 NEW
-will
NOT
come with accessories -- BOTH batteries are included
(5) INCH QUAD  /  Parts built and installed are as follows.. ~>      ARTMAN BEAVER
-White Foxeer mini camera-TBS mini (not racing) vtx maxing 800mw
-Joshua Bardwell F4 flight controller
Betaflight OSD w/240a current sensor
4x UARTS for FRSKY, SBUS, IBUS, SAT (2 inverted UARTS)
Power Out: 3x 5v, 1x 3.3v, 1x VBAT, 1x VTX filtered power (9v), 1x Camera filtered power (9v)
Smart Audio compatibility and Camera Control capability
Programmable LED pin
Buzzer pins
Pre-flashed with BF 3.2.2 - Compatible with CLRACINGF4.hex
Blackbox capability
Included and installed vibration dampeners/gummies
Single Current Shunt Version
Weight: 7.29g
-Speedybee BLS 8Bit 55A 3-6 4in1 ESC-Hypertrain motors 2306 size 1850Kv
-ELRS Rx nano receiver (NEW) incased in tight colored heat shrink!
——— ~> MIND to connect to ELRS related TX, get receiver into bind mode by plugging a (6) cell battery xt60 (3) times into the drone quickly, the third time leaving it plugged in and the receiver should be double flashing blue!
(5) INCH QUAD  /  Parts built and installed are as follows.. ~>      ARTMAN BEAVER
-Yellow Runcam mini camera-Foxeer Reaper Extreme vtx maxing 1W-Speedybee F722 3-6 flight controller
MCU: STM32F722
IMU: BMI270
USB: Type-C
Baro: BMP280 (I2C)
OSD: BetaFlight OSD w/ AT7456E chip
BLE Support, used for Flight Controller configuration
WiFi Support, used for data transfer, e.g firmware
flashing, and Blackbox analysis.
DJI Air Unit plug: A full DJI Air Unit JST slot onboard
BlackBox: 500MB onboard data flash
BetaFlight Camera Control Pad: Yes
Power input: 3S - 6S Lipo
10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
ESC signal M1 - M4 on bottom side and M5-M8 on front side.
UART: 5 sets (UART1, UART2, UART3, UART4, UART6)
ESC Telemetry: UART UART4 RX
I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
LED: Used for WS2812 LED controlled by Betaflight firmware.
Buzzer: BZ+ and BZ- pad used for 5V Buzzer
Boot button: Yes
RSSI input: Yes
SmartPort: Supported
Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
Target: SPEEDYBEEF7V3
Mounting: 30.5x30.5mm, 4mm hole size
Dimension: 41(L) x 38(W) x 8.1(H)mm
Weight: 9g
-IFlight 50A 3-6 ESC-BOSH motors 2306 size 1750Kv
-ELRS Rx nano receiver (NEW) incased in tight colored heat shrink!
——— ~> MIND to connect to ELRS related TX, get receiver into bind mode by plugging a (6) cell battery xt60 (3) times into the drone quickly, the third time leaving it plugged in and the receiver should be double flashing blue!
(3) INCH QUAD  /  Parts built and installed are as follows.. ~>       GEPRC25
-Foxeer Predator nano camera
-
TBS mini (not racing) vtx maxing 800mw -Foxeer reaper AIO V4 F745 45A BLS 2-6
CPU: STM32F745
Power Supply: 2~4S Lipo
BEC Output: DC5V/2A
OSD: BF OSD
Black Box: 16M Flash Memory
UART: 5 Set
USB: Micro USB
Fireware: BF:FOXEERF745V4_AIO
DJI Connector: Supported, 8pin
Size: 32.5X32.5mm
Mounting Hole: 25.5X25.5mm,
Φ
3mm/M2
Weight: 8.6g
Working Temperature: -20
℃
~ +55
℃
Working Humidity: 20
～
95%
Storage Temperature: -20
℃
~ +70
℃
Firmware: G-H-30 BLS 16.7
Continuous /Burst Current: 35A x 4/ 45A x 4
Input Voltage: 2-6S Lipo (8.4-25.2V)
Telemetry: No
ESC Programming: BLHeli-S
Stick Programming: Supported
Current sensor: Supported
Current scale: 100
Input signal: Dshot300/600
-Foxeer motors 1404 size 3850Kv
-Crossfire Rx
nano receiver (NEW) incased in tight colored heat shrink!
2x BETAFPV FIRE LIPO BAGS
9x Pizza Batteries at 1200mAh 6S
1x HLRC Battery at 1500mAh 6S
1xR-Line Battery at 850mAh 4S
ToolRC POWER & Parallel Charging Board
-comes with some battery reading equipment to make sure the batteries are in good health
LOTS OF TOOLS & NEW TS100 Solder Iron & with Carbon Carry Pouch
EXTRA FRAMES
HEAT SHRINK & FAN
2x BINS FULL OF WORKING PARTS
-From motors to mini fc,s to brand new analog vtxs in addition having replacement carbon arms for frames to also including antennas & receivers for crossfire and elrs!   LMK FOR MORE DETAILS
WILL also include a sets of PROPS! & STRAPS
NOTE TOO: PROPS are set to be facing inwards to the stack (fc) & (ESC). ALL QUADS..
THIS FASIRLY CONCLUEDS MOST OF WHATS SHOWN IN THE PICTURES IF INTRESTED OR HAVE ANY QUESTIONS OR DETAILS REGARDING THE ITEMS SHOW ABOVE PLEASE REACH OUT!
THANKS!!